Apeks WTX-D Basic Twin System

SKU
AKWTXBTSYSTEM

From £423.00

To £604.00

               

Apeks WTX-D Twinset setup includes Deluxe 1 Piece Harness, Aluminium Backplate and WTX-D45 wing. Customise your setup with your choice of Backplate and wing size 

(Regulators NOT Included)

WTX-D Twin Cylinder Wing

The WTX and WTX-D Series is a selection of harnesses, buoyancy cells and accessories which offer unparalleled versatility due to the modular nature of the whole system. Each component can be configured into a highly technical rig for those trained to push the limits, or scaled down to make a travel friendly set up suitable for any diver.

The WTX-D twin cylinder wings are designed for twin set diving and perfectly complement the Apeks range of twin manifolds and the Tek3 regulators. Often referred to as donuts, the WTX-D wings are oval shaped air cells or bladders that are not permanently attached to a harness. Not only are these donut wings streamlined, but due to their shape being a continuous loop, they are very stable underwater. There is no dramatic shift of air from left to right.

The Apeks twin cylinder wings are a smart design that allows a cylinder to nest deep inside them. These wings mate up nicely to the rest of the Apeks WTX collection of high quality harnesses, plates and accessories. They can be configured in multiple ways to match the type of diving that you do. As with the rest of the WTX collection, the wings are built from the finest quality materials. They are designed by Apeks and built in our own factory.

Inflator

  • K style with brass buttons
  • Low profile 16” oval-shaped hose
  • Safety cable to prevent hyper-extension
  • Positioned off-centre so as not to interfere with regulator 1st stage

Dump Valve

  • Low profile flat valve
  • Positioned in front, lower-left side

Drains:

  • 2 large drain grommets
  • Centre mesh drain panel

Materials:

  • Exterior: 1000D Armorshield Cordura
  • Inner air cell: 22mil (.022) thick black urethane
  • Zipper: heavy duty YKK #10 plastic zip and slide

Deluxe One-Piece Web Harness

This simple, yet strong, harness can take the load of a fully rigged technical diver and can be easily customised with the hardware of your choice.

Please note that the back plate is not included and must be purchased separately. Your back plate options for this harness are the WTX Aluminium Back Plate, the WTX Stainless Steel Back Plate and the Ultralight Travel Plate. Tank bands are also not included.

  • 12ft. of solid 2” (5cm) webbing with centre grommet
  • 2” (5cm) wide crotch strap
  • 6 stainless 2” (5cm) D-rings
  • Includes neoprene shoulder protectors
  • 2 elastic retaining loops on shoulders and one on crotch strap
  • Heavy duty stainless waist buckle
  • 6 stainless serrated retainers

WTX Back Plate

The WTX and WTX-D Series is a selection of harnesses, buoyancy cells and accessories which offer unparalleled versatility due to the modular nature of the whole system. Each component can be configured into a highly technical rig for those trained to push the limits, or scaled down to make a travel friendly set up suitable for any diver.

The backbone of any system - this cleverly designed back plate can be used with the Apeks Deluxe One-piece Webbed Harness, or inserted directly into the WTX Harness. It is available both in stainless steel and aluminium.

  • Offered in either 304 stainless steel or 6061 anodized aluminum alloy.
  • The stainless steel weighs 4.7 lbs (2.15 kg).
  • The aluminum weighs 1.7lbs (780g).
  • 4 each upper and lower slots accommodate nylon cylinder bands so a single cylinder can be strapped directly to the plate. Having a series of 4 slots provides lateral stability of the cylinder that traditional 2 slot plates cannot.
  • 3 holes at the top of the plate offer a range of height adjustments for the buoyancy cells and the cylinders. In addition, a corresponding lower centre slot allows for lower band bolts that are misaligned.
  • 2” wide crotch strap slot.
  • Upper and lower perimeter holes along either side and holes along the bottom allow for the mounting of accessories.
  • Both offer an electro-plate finish and a laser-etched Apeks logo to enhance the look of the plate.
Customize Apeks WTX-D Basic Twin System
APEKS Deluxe 1 Piece Web Harness   + £0.00

* Required Fields

Your Customization
Apeks WTX-D Basic Twin System
Apeks WTX-D Basic Twin System

In stock

£423.00

Summary